Alumina (Al2O3)CIP Products

Features

CIP (Rubber Press) Products are highly and homogeneously condensed non-porous products because they are made under the ultra-high pressure in all the directions.
Rubber molds, which are suitable for smaller quantity production but less expensive, are used in the CIP manufacturing process.

Product group : FA-PS99

Our FA-PS99 is the slip casting products with no less than 99.5% pure alumina powder formed under high pressure and sintered at ultra-high temperature achieving high level of intensity.
Superior in non-wetting behavior and wet corrosion resistance against fused slag base or fused metal.
As well as in thermal conduction, refractoriness and wear resistance.

Product group : FA-PS96

Our FA-PS99 is the slip casting products with 96% pure alumina powder formed under high pressure and sintered at ultra-high temperature, in the same way as FA-PS99, achieving high level of intensity.
Superior in corrosion resistance and thermal shock resistance.
Both features and prices range between those of FA-PS99 and FA-PS92.

Product group : FA-PS92

Our FA-PS92 is the slip casting products with 92% pure alumina powder formed under high pressure and sintered at ultra-high temperature, in the same way as FA-PS99, achieving lower cost of production.
Widely used in high intensity insulation parts for heating.

FA-PS99

FA-PS99

FA-PS99(アイボリー),FA-PS96(白色)

FA-PS99(Ivory),FA-PS96(White)

FA-PS96チューブ

FA-PS96 Tube

FA-PS96 Chain

Table of Physical Properties

Product group FA-PS99 FA-PS96 FA-PS92
Materials Alumina 99.5% Alumina 96% Alumina 92%
Appearance Non-porous
Chemical Ingredients
(Wt%)
Al2O3 99.5 96.2 92
SiO2 0.05 2.3 5.5
MgO 0.1 0.6 1.0
Na2O3 0.1 0.2 0.3
CaO - 0.5 0.7
Fe2O3 0.02 0.02 0.05
Specific Gravity
(g/cm3)
3.9 3.6 3.5
Water-absorption Rate
(%)
0.0
Thermal Conductivity
(W/mk)
36 32 17
Flexural Strength
(MPa)
300 300 250
Refractoriness
(℃)
1800 1700 1600
Impedance
(20℃,Ωcm)
No less than 1013
Thermal Shock Resistance
(℃/hr)
300
Color Appearance Ivory White
Intended Application Chemistry Laboratory Instruments
Metal Melting Crucibles
Wear Resistant Parts
Protection Tube
Sintering Container for Electronic Parts
Wear Resistant Parts
Pipe Insulation
Insulation Parts
Ceramic Insulators for Electric Heater

Variety of Our Products and Measurement Table  (FA-PS99 Alumina 99.5% Non-porous)

We will produce the item in sizes other than those shown below for a minimum order quantity of 5.
Inquiry or Estimation Request is Free of Charge.

Sagger (Boat / Rod)

※ Top surface being ground

Catalog Number Outer Length(A) Inner Length(B) Height(C) Wall Thickness(D)
□65 × 65h 65 57 65 4
□84 × 45h 84 78 45 3
□112 × 65h 112 100 65 6
□142 × 45h 142 130 45 6
□158 × 19.5h 158 146 19.5 6
アルミナCIP(ラバープレス)成形品 サヤ(こうばち、トレー、バット)寸法図

【 Measurement Chart 】

Frame

※ Top and bottom surface being ground

Catalog Number Outer Length(E) Inner Length(F) Height(G) Wall Thickness(H)
□65 × 25h 65 57 25 4
□113 × 50h 113 102 50 5.5
□120 × 40h 120 109 40 5.5
□243 × 200h 243 223 200 10
アルミナCIP(ラバープレス)成形品 枠(ワク)寸法図

【 Measurement Chart 】

Plates (Setters / Lids))

※ Top and bottom surface being ground

Catalog Number Outer Length(I) Thickness(J)
□65 × 4t 65 4
□88 × 4t 88 4
□115 × 4t 115 4
□123 × 5t 123 5
□145 × 5t 145 5
□154 × 5t 154 5
□162 × 5t 162 5
□260 × 7t 260 7
アルミナCIP(ラバープレス)成形品 板(セッター、フタ)寸法図

【 Measurement Chart 】

Crucibles

※ Top surface being ground as necessary

Catalog Number Outer Diameter(K) Inner Diameter(L) Height(M) Wall Thickness(N)
Ø15 × 100h 15 12 100 1.5
Ø30 × 150h 30 24 150 3
Ø40 × 140h 40 33 140 3.5
Ø50 × 150h 50 42 150 4
Ø60 × 150h 60 52 150 4
Ø80 × 150h 80 71 140 4.5
Ø100 × 150h 100 91 150 4.5
Ø126 × 230h 126 116 230 5
Ø145 × 230h 145 135 230 5
Ø205 × 325h 205 185 325 10
Ø233 × 325h 233 213 325 10
アルミナCIP(ラバープレス)成形品 ルツボ寸法図

【 Measurement Chart 】